- Pair each resource with a room mailbox (two-way sync)
- Take over Exchange appointments as blockers in anny automatically and avoid double bookings
- Import many rooms at once from your Exchange room lists and have missing resources created right away
How the Exchange Server connection works
The connection uses a service account in your Active Directory. The account needs either the ApplicationImpersonation role on the room mailboxes or full access to each room mailbox. anny connects from outside to your server’s EWS endpoint over HTTPS (port 443); your server does not need to open any connections towards anny.
anny writes the appointments to the room calendar without sending invitations or cancellations to attendees and marks them as “busy”. Exchange reports changes in the room calendars over a standing connection; in addition, anny regularly checks all connected rooms so that no change gets lost.
Connect Exchange Server
Requirements
Before you connect Exchange Server, make sure you have:- The Calendar synchronization feature in your plan. Without it, the integration does not appear under Account › Apps & Integrations.
- Admin rights in your anny account
- Exchange Server 2016, 2019 or Subscription Edition with room mailboxes for your rooms
- A service account with the ApplicationImpersonation role on the room mailboxes or with full access to each room mailbox
- An EWS endpoint that is reachable from the internet over HTTPS without pre-authentication
- A firewall rule that allows anny’s addresses (see below)
Allow anny in your firewall
anny connects to your Exchange from fixed IP addresses. In your firewall, allow incoming connections from these addresses on port 443 to your EWS endpoint:
The setup also shows the addresses for your environment in the Firewall box. If no address is shown there, our support gives you the addresses for your environment.
Set up the connection
1
Create the integration
In the sidebar, open Account › Apps & Integrations, select Microsoft Exchange Server under All Apps and Integrations and click Set up.
2
Enter the service account
Fill in the fields:
3
Connect and verify
Click Connect and verify. anny signs in with the service account and opens the test mailbox. anny only stores the credentials once Exchange accepts the account. If the check fails, anny shows the reason (see Troubleshooting).
4
Connect rooms
In the Rooms section, connect each resource to a room mailbox: one by one via Add, or many at once via Import rooms (see the next section).To connect a single room, choose the anny resource under Select resource and the room under Room from your room lists. If your organization has no room lists, enter the Room mailbox address directly. Click Confirm.
5
Activate
Activate the integration via the toggle in the page header. anny then syncs all future appointments and bookings of the connected rooms.
Import rooms
With Import rooms, you connect many rooms from your Exchange room lists at once, even several hundred.1
Pick a room list
In the Rooms section, click Import rooms and choose a single list or All room lists under Room list.
2
Create missing resources
Leave Create missing resources on if anny should create new resources for rooms without a matching resource. If you switch it off, anny skips those rooms.
3
Check the preview
Click Preview. anny shows how many rooms it would Link to existing resource, for how many it would Create new resource, which are Already connected, and which are Skipped, no matching resource.
4
Import
Click Import. anny connects the rooms in batches and shows the progress. If the integration is already active, the sync for the new rooms starts right away.
- If a room’s name matches a resource exactly, anny links it to that resource. Upper and lower case do not matter. If several resources share the name, anny creates a new resource rather than linking the wrong one.
- Archived resources, sub-resources, and resources already connected to a room are not linked.
- New resources are not live yet. They take over your organization’s location and time zone and are placed in your first category. Review them and set them live once they are fully set up.
- Rooms already connected stay as they are. A second import only adds new rooms.
New resources count against your plan just like resources created in the admin. If your plan does not allow that many new resources, the preview shows a notice and the import does not start. In that case, switch off Create missing resources or pick a smaller room list.
Limitations
The Exchange Server integration does not support:- Exchange Online: For mailboxes in Microsoft 365, use the Microsoft 365 integration.
- Personal calendars: It connects room mailboxes, not employees’ personal mailboxes.
- Appointments as bookings: Exchange appointments are always taken over as blockers.
- Nested room lists: Rooms from room lists inside a room list do not appear in the picker or the import. You can connect them one by one via the room mailbox address.
- Access without a firewall rule: anny has to reach your EWS endpoint directly from the internet. A sign-in page in front of it, for example a reverse proxy with pre-authentication, prevents the connection.
FAQ
Do attendees get invitations from Exchange?
Do attendees get invitations from Exchange?
No. anny creates, updates, and removes the appointments directly in the room calendar without sending invitations or cancellations.
How fast are changes synced?
How fast are changes synced?
Booking changes in anny are transferred immediately. Exchange usually reports changes in the room calendar within a few seconds. In addition, anny regularly checks all connected rooms.
Does my Exchange Server have to connect to anny?
Does my Exchange Server have to connect to anny?
No. Only anny connects to your server, over HTTPS on port 443. You only need to allow anny’s IP addresses in your firewall.
Which sign-in should I choose?
Which sign-in should I choose?
We recommend NTLM. anny also supports servers with Extended Protection enabled. Basic over HTTPS only works if Basic authentication is allowed for EWS on your server.
Troubleshooting
"Exchange Server not reachable"
"Exchange Server not reachable"
anny cannot reach Exchange Web Services at the address you entered. Check the EWS URL, that the endpoint is reachable from the internet without pre-authentication, and that anny’s IP addresses are allowed in your firewall. A firewall that drops the connection is the most common cause.
"Authentication failed"
"Authentication failed"
Exchange rejected the service account. Check the user name (
DOMAIN\user or UPN), the password, and the selected Sign-in."Mailbox not reachable"
"Mailbox not reachable"
The service account cannot open the test mailbox. Check the test mailbox address and that the account holds the ApplicationImpersonation role or full access to the mailbox.
A room shows "Room mailbox unreachable"
A room shows "Room mailbox unreachable"
The service account may not access this room mailbox, or the address is wrong. Check the service account’s access to the mailbox and the room mailbox address.